[. . . ] 25
This appliance is intended for use in the home and the home environment. Use the dishwasher only in the household and only for its designed purpose: for washing domestic dishes.
Fault, what to do?38
yf tS e a
Safety instructions
sic nusi otrtn
Children from 8 years of age or people whose physical, sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person. Before you switch ON the appliance Please read the operating and installation instructions carefully. [. . . ] The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils.
Operating the appliance
ga ntr iO e p eiph c at nl e a
Programme data
The programme data (consumption values) can be found in the summary of instructions. water temperature or line pressure may result in deviations.
Aquasensor
Aqua sensor *
* depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
21
en
Operating the appliance
Remaining running time display
When the programme is selected, the remaining running time of the programme is indicated on the digital display )". The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
Switching off automatically after the end of the programme *
Switchingof automaticalyafterthe ndoftheprogram e
Timerprogram ing
Timer programming *
* depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. Press @ + or – button until the displayed time corresponds with your requirements. To delete timer programming, press the @ + or – button until )" : is indicated on the digital display. You can change your programme selection at any time until the programme starts.
End of programme
The programme has ended when the value : is indicated on the numerical display )".
* depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). : Appliance does not switch off automatically : Off after 1 min : Off after 120 min 1. The LED for button # flashes and the digital display )" displays the factory setting : . Press programme button # until the factory set value : is indicated on the digital display )". Each time the button is pressed, the set value increases by one level; when the value of : has been reached, the display jumps back to : (off). The set value is saved.
22
Operating the appliance
en
Switching off the appliance
Short time after the end of the programme: 1. Note When the programme ends, leave the appliance to cool down a while before opening it. This will prevent steam from escaping and causing longterm damage to your built-in furniture.
Changing the programme
When the START button P has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset).
Intensive drying
The final rinse uses a higher temperature which improves the drying result. Hold down programme button # and press START button P until the digital display )" : . . . The LED for button # flashes and the digital display )" displays the factory setting : . Press programme button # until the factory set value : is indicated on the digital display )". If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. To continue the programme, switch on the ON/OFF switch ( again.
Terminatingtheprogram e
Terminating the programme (Reset)
1. Switch off ON/OFF switch (.
23
en
Cleaning and maintenance
Cleaning and maintenance
gC ne i nl a d n a en cm nti aa e
A regular inspection and maintenance of your machine will help to prevent faults. [. . . ] Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts. Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out!
36
Installation and connection
en
Drinking water connection
1. Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts. Ensure that the drinking water connection is not kinked, crushed or twisted. [. . . ]